How to Fix Netgear Extender WPS Light Blinking But Not Connecting Issue?

Feb 16, 2024 | Troubleshooting, Blog | 0 comments

Is your Netgear WiFi extender’s WPS light causing you grief by not turning on or repeatedly blinking? Don’t waste time aimlessly troubleshooting – this guide will walk you through the key steps to diagnose and fix the most common Netgear extender WPS light errors.

The WPS (WiFi Protected Setup) light on Netgear boosters and extenders serves an important function – it shows the status of the wireless connection process. When working normally, the light should turn solid blue or green once a secure link with your router is established. However, the WPS light may start malfunctioning over time and display unusual blinking patterns or even refuse to turn on at all.

By learning what the WPS light behavior signifies and following some basic troubleshooting, you can get your Netgear extender back up and running optimally. We’ll cover the most reported issues – Netgear Extender WPS Light Blinking But Not Connecting. With the right information and a few simple setup tweaks, your troublesome WPS indicator will be back to steady in no time.

What is the Netgear Extender Device Light?

The Netgear extender comes equipped with various LED lights that indicate the status of the device. These LED lights are located on the front or top panel of the extender and are very useful for troubleshooting connectivity issues.

Power LED

The Power LED confirms that the extender is receiving the required power through the electrical outlet. It is typically green when the extender is turned on and receiving power. If this LED is off, it means a power issue is preventing the extender from turning on.

This LED indicates if the extender is in range and connected to the host router’s Wi-Fi signal. The Router Link LED will be solid green when optimally connected to the router. If it’s blinking, the connection with the router is poor.

WPS LED

The WPS (Wi-Fi Protected Setup) LED flashes during the WPS pairing process between the extender and WPS-enabled client devices. Once paired, the light will turn solid.

Device LED

The Device LED shows the connection status between the extender and any client devices connected to the extender’s Wi-Fi network.

  1. A solid green Device LED indicates active connected devices with good signal strength.
  2. If it’s blinking, the client devices have a weak connection.
  3. However, if the Netgear extender Device LED is off, points to connectivity issues between the extender and devices.

By looking at the various LED lights on the Netgear extender, you can quickly diagnose where the problem lies if you have any wireless connectivity issues. The Device LED specifically helps in determining problems with client devices connecting to the extender.

Reasons for Netgear Extender WPS Light Blinking But Not Connecting

It can be frustrating when your Netgear extender’s WPS light is blinking but not actually connecting to your main router. The WPS light flashing indicates the extender is trying to establish a wireless connection using WiFi Protected Setup (WPS). However, its failure to solidly connect points to some interference in the pairing process.

There are a few potential reasons the WPS connection may be failing between your Netgear router and extender:

  1. They may not be within close enough range. Try moving the extender closer to the router during the WPS pairing attempt to see if it is an issue of distance. Extenders typically need to be within 5 feet during setup.
  2. The extender and router may not actually have compatible WPS. Older routers sometimes do not support the latest WPS standards. Check your router’s specifications to confirm WPS compatibility. If not supported, you’ll have to connect them manually instead.
  3. Too many wireless networks in the area can cause connection issues. Try turning off other nearby WiFi routers and devices to eliminate signal interference during WPS pairing. Also, be sure your extender and main router are on different channels.
  4. There may already be too many devices connected to your router. The extender may not be able to pair if your main router’s capacity is reached. Disconnect some devices first before attempting WPS again.

Solution for Netgear Extender WPS Light Blinking But Not Connecting

If the WPS light on your Netgear WiFi extender is blinking but failing to connect to your router, try these steps:

  1. Ensure the extender and router are within close range, ideally within 5 feet, during the WPS pairing process. Being too far apart can cause connectivity issues. Check out our article on where to place the WiFi extender for the best coverage.
  2. Check if your router supports WPS. Some older routers do not work with the WPS standard. Refer to your router documentation to verify WPS compatibility.
  3. Eliminate wireless interference by turning off nearby WiFi routers and devices while attempting to pair. Also, switch your extender and router to different channels to avoid conflicts.
  4. Reduce the number of connected devices on your main router. If the router has reached maximum capacity, the extender may struggle to connect via WPS.
  5. Try using the manual wireless connection method instead of WPS. Access your extender’s web-based setup page to configure it.
  6. Update the firmware on both the extender and router. Old firmware can sometimes cause WPS pairing problems.

If you still cannot get the WPS connection to succeed after multiple tries, reset both the extender and router to factory default settings. This clears any errors preventing WPS from completing properly. As a last resort, use the manual wireless connection method by accessing the extender’s web-based setup page instead of WPS. You need to contact Netgear support if problems continue even when directly connected.

How Do I Reset My Netgear Extender to Fix WPS Light Issues?

If you have tried the usual troubleshooting steps but your Netgear extender’s WPS light continues blinking or having connection issues, resetting the extender to factory default settings often helps resolve problems.

Resetting clears out any corrupted software or glitches that may be causing the WPS light errors. It erases all custom settings and returns the extender to its original out-of-the-box state. Just be aware that resetting will remove your WiFi network names, passwords, and any connection specifics you had configured.

Here are the step-by-step instructions to reset a Netgear extender:

  1. Locate the Factory Reset button on your extender model. It is typically a recessed button requiring a pin or paperclip to press.
  2. Press and hold the Factory Reset button for at least 7 seconds until the extender’s lights begin flashing.
  3. Once the reset process completes after about 1 minute, the lights will turn off.
  4. Unplug the extender, wait 10 seconds, and plug it back in. This powers it back on after the reset.
  5. The extender will boot up with factory settings restored. Try adding it to your WiFi network again via WPS.

Resetting the extender essentially gives you a fresh start for troubleshooting the WPS light. Just remember you’ll have to reconnect it to your WiFi network and router. If problems recur, contact Netgear support for replacement options.

Wrapping Up

Having an unresponsive, blinking, or otherwise erratic WPS light on your Netgear range extender can impede its ability to boost your WiFi signal. By taking the time to diagnose the cause and methodically trying fixes like power cycling, resetting, and manually reconfiguring, you can get the WPS function operating normally again.

Remember, consistent flashing that won’t solidify often just means interference is disrupting the wireless connection handshake between router and extender. Changing locations, and proximity, and reducing competing signals will help stabilize the linkup. And don’t hesitate to rely on a factory reset when your WPS light seems possessed!

With the guidelines provided in this guide, your Netgear extender’s WPS light woes will be banished in no time. Just be patient, work through each troubleshooting stage, and reset when unsure. Contact Netgear support if problems continue to persist. Here’s to smooth sailing WiFi expansion from now on!

Article you might be interested in How to Connect a WiFi Extender to Your Router?

Why is the WPS light on my Netgear extender not turning on?

The main reasons are a loose power connection, hardware failure, or the extender needing a reset.

I plugged in my Netgear extender but the WPS light is still off, what should I check?

Verify the power cable is firmly inserted in the outlet and extender. Try a different outlet you know works.

Could my Netgear extender have a hardware issue causing the WPS light to stay off?

It’s possible. An internal hardware failure like the power supply or electrical wiring could prevent the WPS light from turning on.

Will resetting my Netgear extender potentially fix the WPS light not turning on?

Yes, resetting the extender often resolves software-related issues that may be preventing the WPS light from powering on.

How do I reset my Netgear extender to factory settings?

Press and hold the recessed Factory Reset button for 7+ seconds until the lights blink. Unplug and reconnect power.

I reset my extender and the WPS light still won’t turn on, what now?

If a reset does not resolve the WPS light issue, the extender likely requires replacement due to a hardware problem. Contact Netgear.

Where can I find the Factory Reset button on my Netgear extender model?

It’s typically a small recessed button that needs a pin or paper clip to press in. Check your user manual for the exact location.

Will resetting delete all my WiFi network settings and passwords?

Yes, resetting erases any custom settings, so you’ll need to reconfigure the extender’s wireless connections afterward.

Last Updated on February 23, 2024

0 Comments

Submit a Comment

Your email address will not be published. Required fields are marked *

8 − 8 =

Share This